- Research article
- Open Access
- Open Peer Review
This article has Open Peer Review reports available.
Accumulation and transport of microbial-size particles in a pressure protected model burn unit: CFD simulations and experimental evidence
© Beauchêne et al; licensee BioMed Central Ltd. 2011
Received: 17 June 2010
Accepted: 3 March 2011
Published: 3 March 2011
Controlling airborne contamination is of major importance in burn units because of the high susceptibility of burned patients to infections and the unique environmental conditions that can accentuate the infection risk. In particular the required elevated temperatures in the patient room can create thermal convection flows which can transport airborne contaminates throughout the unit. In order to estimate this risk and optimize the design of an intensive care room intended to host severely burned patients, we have relied on a computational fluid dynamic methodology (CFD).
The study was carried out in 4 steps: i) patient room design, ii) CFD simulations of patient room design to model air flows throughout the patient room, adjacent anterooms and the corridor, iii) construction of a prototype room and subsequent experimental studies to characterize its performance iv) qualitative comparison of the tendencies between CFD prediction and experimental results. The Electricité De France (EDF) open-source software Code_Saturne ® (http://www.code-saturne.org) was used and CFD simulations were conducted with an hexahedral mesh containing about 300 000 computational cells. The computational domain included the treatment room and two anterooms including equipment, staff and patient. Experiments with inert aerosol particles followed by time-resolved particle counting were conducted in the prototype room for comparison with the CFD observations.
We found that thermal convection can create contaminated zones near the ceiling of the room, which can subsequently lead to contaminate transfer in adjacent rooms. Experimental confirmation of these phenomena agreed well with CFD predictions and showed that particles greater than one micron (i.e. bacterial or fungal spore sizes) can be influenced by these thermally induced flows. When the temperature difference between rooms was 7°C, a significant contamination transfer was observed to enter into the positive pressure room when the access door was opened, while 2°C had little effect. Based on these findings the constructed burn unit was outfitted with supplemental air exhaust ducts over the doors to compensate for the thermal convective flows.
CFD simulations proved to be a particularly useful tool for the design and optimization of a burn unit treatment room. Our results, which have been confirmed qualitatively by experimental investigation, stressed that airborne transfer of microbial size particles via thermal convection flows are able to bypass the protective overpressure in the patient room, which can represent a potential risk of cross contamination between rooms in protected environments.
Infections in burn patients are a major cause of morbidity and mortality due to cumulative risk factors such as the burn injury itself, the immunodeficiency related to extended burn wounds, aggressive therapy and prolonged hospitalization. Microorganisms that cause these infections include bacteria, fungi and viruses [1, 2] and are commonly found in the patient's own endogenous flora, but can also originate from exogenous sources and from health care personnel. Noteworthy are Acitenobacter, Pseudomonas and resistant Staphyloccocus aureus which have been responsible for outbreaks in burn units [3, 4]. Modes of transmission to the patient include contact, droplet and airborne spread [1, 4]. Moreover, environmental conditions in these units call for elevated temperatures (>30°C) and humidity levels (>50% RH) which could facilitate microbial growth and environmental contamination.
Although the incidence of burn wound infections has declined in recent years, infection rates remain high in patients with burns that exceed 30% of the total body surface area . Preventing direct transmission of infection in burn patients relies on strict application of disinfection and sterilization guidelines. The objective is to both prevent any microbial entry into the room, and simultaneously avoid any microbial diffusion from exiting and reaching adjacent rooms. This is particularly important for burn patients because of the high exposed surface area they have in contact with room air and their high propensity to endogenous acquired infections.
Infection risk is also influenced by the design of burn unit rooms,  and it has been shown that the use of single bed isolation [6, 7], pre-emptive barrier precautions  and laminar airflow isolation  can be effective protection measures to prevent cross transmission and outbreaks . However, basic knowledge of room design parameters is lacking and must take into account the unique environmental factors that these locations require (e.g. elevated temperature and humidity). In particular, thermo-convective air flows that can transport airborne contaminates from adjacent rooms and throughout the unit need to be considered. Thus, we have used Computational Fluid Dynamic (CFD), which incorporate thermal sources and the opening and closing of room access doors, as a tool for optimizing the design of an intensive care room for severely burned patients . Based on these simulations, a prototype room was constructed and experimental control measurements were carried out and used for validation and direct comparison with the CFD predictions.
The initial room design was made using knowledge acquired from the medical staff and hospital engineering department, taking into account that such rooms will be used for intensive care, complex dressing, showering and surgical treatment of burn patients, and that the patient's stay can last from up to 2 weeks to several months for the most severe cases.
Computational Fluid Dynamic simulations (CFD)
CFD analysis of the initial room design was performed using the Electricité De France (EDF) software Code_Saturne ® . The software is based on a Eulerian unstructured co-located finite volume approach that solves incompressible Navier-Stokes equations for meshes with cells of any shape (tetrahedral, hexahedral, prismatic, pyramidal, polyhedral...). The meshes can be grid structured and non conforming. The predictor-corrector method is used for pressure velocity coupling (SIMPLEC algorithm). The transport equation that takes into account the temperature is then solved with an updated velocity. The code does not use by default a Boussinesq approximation but a variable density with a conservation of the mass flow (the time derivative of the density is neglected in the continuity equation at low Mach numbers).
Standard Boundary conditions used for the CFD simulations
Standard logarithmic Wall Function
Dirichlet based on the integral lengthscale
Standard Wall Function
Standard Wall Function with Dirichlet or Neumann boundary conditions
A passive scalar is used to qualitatively follow particles . Additional post-processing is carried out using trajectories to predict high particle density locations. In the case of passive scalar transport, the source (discretized surfaces) is considered as a Dirichlet condition. For post-processing with particles that follow the streamlines, a given number of particles are emitted from the source.
No deposition and re-suspension is taken into account at the wall with both methods.
The mesh consists of about 300,000 hexahedral cells, which represents a very high quality for such CFD computations. No grid sensitivity study has been carried out. Using our experience from previous CFD computations, the present refinement is a priori not sufficient for a perfect convergence of the results but appropriate to have good qualitative results. The computational domain covers the central treatment room and the two anterooms including equipment, with eight staff members and one patient located in the treatment room. Thermal sources in the simulation included 70 W for the patient considered at rest, 135 W for each of the standing and active eight staff members, 200 W for both ceiling lamps, and 965 W for the bedpan washer in the exit anteroom. Both the steady-state condition (RANS), when all doors are closed, and the transient regime (URANS), with either the entry or exit anteroom room door open, were simulated to track transportation of airborne contaminates.
Prototype burn unit
A prototype burn treatment unit, which closely followed the initial room design used for CFD simulations, was constructed at St-Louis Hospital, Paris, France. Due to architectural constraints, the actual anterooms were slightly smaller and three exhaust grilles located at 0.15, 1.0 and 1.8 meters above the floor in the corners of the central treatment room were used instead of two. All other air supply and exhaust configurations corresponded to those of the initial room design. Supply air was treated by state-of-the-art HEPA-MD units, supplied by the company AirInSpace S.A.S., Montigny-le-Bretonneux, France, which were installed in the air distribution ventilation system. These units ensured HEPA-grade filtration and biological decontamination of the air supplied to the central treatment room. The air-flow, room pressures and temperatures were all maintained in accordance with the initial room design criteria.
The central room was equipped with an operating table and suspended overhead operating lights. Six mannequins equipped with 100 W lamps were used to simulate surgical staff in the central room. 200 W and 500 W convector heaters were also placed in the room to further simulate heat fluxes arising from diverse medical equipment.
Measurements within the prototype burn unit
Time-series measurements of airborne particle concentrations in the treatment and anterooms were used to experimentally validate the simulated predictions of how airborne particles are transported throughout the prototype burn unit. In order to match with the CFD passive scalar particulate transportation model used, a dry inert powder having a particle size range from 0.5 to 20 μm, was aerosolized in the treatment room to mimic airborne contamination  The powder was injected into the air using a dust generator (SAG410, Topas) at different locations so as to trace particle movements in various areas throughout the rooms. Measurements of the airborne particle concentration were made using a 6-channel light-scattering particle counter (Climet, CI-450t) with readings covering the particulate sizes of the dry inert powder.
Additional file 1: Movie1 - patient room. Dynamic representation of air-flows in the patient room with source contamination arising from the patient table. Colors represent the fraction of source contamination, with highest concentrations in red and lowest in blue. A contamination accumulation is entrained by heat convection currents into the upper part of the room between the air diffusion panels and room walls. (mpeg2 movie sequence) (MPEG 16 MB)
Additional file 2: Movie2 - entry sequence. CFD simulation of the sequential entry into the patient room through the anteroom, showing a "thermal switch" between patient room and anteroom. When the door is open, (T = 1065s-1070s), warm air (32°C) is aspirated into the adjacent anteroom near the top of the door entrance, while cooler air (25°C) from the anteroom is drawn into the patient room at floor level. (mpeg2 movie sequence) (MPEG 7 MB)
Additional file 3: Movie3 - exit sequence. CFD simulation of the sequential entry into the patient room through the anteroom When the door is open, (T = 1670s-1675s) no significant transfer is observed between patient room and anteroom that were at the same temperature (32°C). (mpeg2 movie sequence) (MPEG 6 MB)
Qualitative validation of CFD findings in the prototype room
Experimental measurements were carried out to evaluate the CFD predictions and determine if the effects of heat convection currents and thermal transport influence airborne particulate contamination. For these studies the constructed treatment room was used with the ventilation system, mannequins, lights and artificial equipment all in operation so as to simulate CFD conditions and to provide a realistic model scenario.
To study the thermal convection of particles between rooms, the constructed burn unit was placed in operation and the airborne particle levels were monitored while the sliding room access doors were opened and closed (Figure 4b). Figure 4b presents the results for 1 μm-5 μm particle levels near the door in the upper portion of the entry anteroom at 25°C (-15 Pa) (filled squares) and in the lower portion of the treatment room at 32°C (+20 Pa) (open circles). The particle generator was placed in the treatment room and ran continuously for ten minutes (hatched area). Concentration measurements were taken simultaneously at one-minute intervals. Arrows in the figure indicate the times at which the sliding door was opened for a 10 second period. It can clearly be seen that a spike in the airborne contamination level inside the treatment room is witnessed after each door opening and that the relative importance of this spike is increased when the overall contamination is lower. In contrast to this, comparing door openings between the anteroom at 25°C (-15 Pa) and corridor at 27°C (0 Pa) with particle contamination taking place inside the anteroom, very little contaminate transfer is witnessed during the contamination period with no detectable transfer afterwards (data not shown). Noteworthy, similar trends of concentration ratios were observed for smaller particle sizes (0.5 μm-1 μm) but with lower quantitative impact of the artificial contamination period than the data presented (data not shown). Concentrations of particles for sizes above 5 μm were negligible even during the artificial contamination period (data not shown).
CFD is a powerful analytical tool for understanding flows and transport of microorganisms in protected environments and hospital settings [13, 14]. It has already been used for improving the control of airborne particles in operating theatres showing that room geometry, airflow rates, air velocity profiles, distribution of heat sources and operating lights were determinant for the containment of infection [15, 16]. However, to our knowledge, CFD has been rarely used for assisting the design of burn units . Moreover, the majority of work has focused on pressure-driven air flows, and not heat-induced motion and its consequences. This later point is particularly relevant to burn units due to their unique environmental conditions and high risk of patient infection [1, 4], which has served as the stimulus for us to use CFD analysis in the design of our prototype burn unit and to investigate several scenarios. To that end we have found that temperature gradients can play an important role in the distribution of airborne contaminates and careful analysis of air flows should take these into account. As seen in CFD simulations and particle tracer experiments, heat convective currents can trap suspended particles in so-called "hot spots". In itself the presence of these spots represent a contaminate source risk, and in addition to this the problem can be aggravated, leading to further risk through transport to adjacent rooms due to differential room temperatures that create thermal convective flows. This finding led us to take corrective engineering measures that called for enhanced exhaust flows in the upper section of the treatment room near the access doors.
Indeed, the risk of occasional small back flow created when doors are open simultaneously or when there is a high difference of temperature across an open door has already been considered in the design of ventilation system in healthcare facilities . Here we provide a CFD evidence of this phenomenon and show its consequences in terms of real particle transfer between pressurized rooms for small particle sizes (<5 μm). We note that, due to the lack of sufficient concentrations of particles above 5 μm in our experiments, we are unable to make conclusions within this size range.
We have found that when a temperature difference of 7°C existed between the rooms, inter-room thermal convective flows predicted by CFD and qualitatively verified experimentally were important enough to transport airborne contamination into the positive pressure treatment room when the access door was opened, despite an initial 35 Pa pressure difference between the rooms when the doors are closed. However, with only a 2°C temperature difference we observed only negligible effects even when lower initial pressure differences were opposing the thermal convection (15 Pa).
These observations are consistent with recent work by Dong et al. , who report a similar phenomenon using tracer gas measurements to confirm their predictions and assumed that particle transport could ensue. The present CFD predictions are complimentary to those of Dong et al. and our experimental observations performed with 0.5-20 microns size particles support that transport of bacteria and fungal spores can arise from these convective flows.
In conclusion, CFD simulations proved to be particularly useful for the design and optimization of the burn unit treatment room constructed at St-Louis Hospital. Our results showed the importance of airborne particle transport via thermal convection flows generated by thermal differences between rooms. Such phenomenon has potential consequences in terms of prevention of infections since we showed experimentally that particles with sizes in the range of bacteria or fungal spores were carried by the thermal flow and could bypass the protective overpressure in the patient room. Based on these data, the design of the ventilation system, the choice of room temperatures was amended and health care workers practices were adapted to prevent particle carryover. Although CFD simulation of particle transport has some limitations as a surrogate for microbial behaviour in the environment, we estimate that such phenomenon and pressure bypass is likely to occur in any pressurized room, ward or laboratory and should be considered as a risk of microbial airborne transmission.
This work was supported by a grant from the direction de la Recherche Clinique (PHRC ADR 06059). F. Choukri was supported by a grant from the Agence Française de Sécurité de l'Environnement et des conditions du Travail (AFSSET, convention 07-CRD-29.
We thank Florence Charreyre, Emmanuelle Baillargeat, Sandrine Roncier, Patricia Nathan for their assistance in preparing the layout of the room and acknowledge the support of Christian Boyer and Christian Cuvillier for building the prototype room.
- Church D, Elsayed S, Reid O, Winston B, Lindsay R: Burn wound infections. Clin Microbiol Rev. 2006, 19: 403-434. 10.1128/CMR.19.2.403-434.2006.View ArticlePubMedPubMed CentralGoogle Scholar
- Murray CK, Loo FL, Hospenthal DR, Cancio LC, Jones JA, Kim SH, Holcomb JB, Wade CE, Wolf SE: Incidence of systemic fungal infection and related mortality following severe burns. Burns. 2008, 34: 1108-1112. 10.1016/j.burns.2008.04.007.View ArticlePubMedGoogle Scholar
- Chim H, Tan BH, Song C: Five-year review of infections in a burn intensive care unit: High incidence of Acinetobacter baumannii in a tropical climate. Burns. 2007, 33: 1008-1014. 10.1016/j.burns.2007.03.003.View ArticlePubMedGoogle Scholar
- Weber J, McManus A: Nursing Committee of the International Society for Burn Injuries. Infection control in burn patients. Burns. 2004, 30: A16-24. 10.1016/j.burns.2004.08.003.View ArticlePubMedGoogle Scholar
- Bayat A, Shaaban H, Dodgson A, Dunn KW: Implications for burns unit design following outbreak of multi-resistant Acinetobacter infection in ICU and burns unit. Burns. 2003, 29: 303-306.View ArticlePubMedGoogle Scholar
- McManus AT, Mason AD, McManus WF, Pruitt BA: A decade of reduced gram-negative infections and mortality associated with improved isolation of burned patients. Arch Surg. 1994, 129: 1306-1309.View ArticlePubMedGoogle Scholar
- Shirani KZ, McManus AT, Vaughan GM, McManus WF, Pruitt BA, Mason AD: Effects of environment on infection in burn patients. Arch Surg. 1986, 121: 31-36.View ArticlePubMedGoogle Scholar
- Safdar N, Marx J, Meyer NA, Maki DG: Effectiveness of preemptive barrier precautions in controlling nosocomial colonization and infection by methicillin-resistant Staphylococcus aureus in a burn unit. Am J Infect Control. 2006, 34: 476-483. 10.1016/j.ajic.2006.01.011.View ArticlePubMedGoogle Scholar
- Demling RH, Maly J: The treatment of burn patients in a laminar airflow environment. Ann N Y Acad Sci. 1980, 353: 294-299. 10.1111/j.1749-6632.1980.tb18932.x.View ArticlePubMedGoogle Scholar
- Fletcher CAJ, Mayer IF, Eghlimi A, Wee KHA: CFD as a building services engineering tool. Int J Arch Sci. 2001, 2: 67-82.Google Scholar
- Archambeau F, Méchitoua N, Sakiz M: Code_Saturne: A finite volume code for the computation of turbulent incompressible flows - Industrial applications, Int. J. on Finite Volume. Electronical edition. 2004, [http://www.ijfv.fr/memo/JOURNAL/PRINTS/saturne.pdf]Google Scholar
- Loomans MGLC, van Houdt W, Lemaire AD, Hensen JLM: Performance assessment of an operating theatre design using CFD simulation and tracer gas measurements. Ind Built Env. 2008, 17: 299-312. 10.1177/1420326X08094948.View ArticleGoogle Scholar
- Jiang Y, Zhao B, Li X, Yang X, Zhang Z, Zhang Y: Investigating a safe ventilation rate for the prevention of indoor SARS transmission: An attempt based on a simulation approach. Build Simul. 2009, 2: 281-289. 10.1007/s12273-009-9325-7.View ArticleGoogle Scholar
- Zhao B, Yang C, Chen C, Feng C, Yang X, Sun L, Gong W, Yu L: How Many Airborne Particles Emitted from a Nurse will Reach the Breathing Zone/Body Surface of the Patient in ISO Class-5 Single-Bed Hospital Protective Environments?--A Numerical Analysis. Aerosol Science and Technology. 2009, 43: 990-1005. 10.1080/02786820903107925.View ArticleGoogle Scholar
- Chow TT, Yang XY: Ventilation performance in operating theatres against airborne infection: review of research activities and practical guidance. J Hosp Infect. 2004, 56: 85-92. 10.1016/j.jhin.2003.09.020.View ArticlePubMedGoogle Scholar
- Memarzadeh F, Manning AP: Comparison of operating room ventilation systems in the protection of the surgical site. ASHRAE Trans. 2002, 108: 3-15.Google Scholar
- Lavedrine I, Thomas P, Tharp J, Sipes J: Innovative design solutions for burn intensive care units. Ninth International IBPSA Conference. 2005, Montréal, Canada, August 15-18, 603-608.Google Scholar
- Department of Health: Estate and facilities division. Health technical memorandum Health Technical Memorandum 03-01: specialised ventilation for health premises. Part A - design and installation. TSO, Norwich UK, 120-Google Scholar
- Dong S, Tu G, Cao R, Yu Z: Numerical study on effects of door-opening on airflow patterns and dynamic cross-contamination in an ISO Class 5 Operating Room. Trans Tianjin Univ. 2009, 15: 210-215. 10.1007/s12209-009-0037-y.View ArticleGoogle Scholar
- The pre-publication history for this paper can be accessed here:http://www.biomedcentral.com/1471-2334/11/58/prepub
This article is published under license to BioMed Central Ltd. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.